HV Series

Flows to 125 GPM
Pressures to 76 ft. TDH

1/2 to 2 horsepower

Recommended for:
Plating Solution Filtering/Circuit Etching
Fume Scrubbing/Pollution Control
Transfer Pumping
Recirculation Pumping/Water Treatment
Photographic chemicals

HV-Pump-Small.jpg (8923 bytes)
Data Sheet - Parts Sheet
     HV Series   horizontal centrifugal pumps are designed to the latest hydraulic technology.  The volute design offer high efficiency and hydraulic balance for the impeller.  All units are supplied with a TEFC motor as standard.

Pump is constructed of CPVC thermoplastic.  Mechanical seal is carbon vs. ceramic (optional carbon vs. silicon carbide) with Viton® elastomer.  The seal configuration can be outside mounted (standard), inside mounted (Diplo) or double water flushed (requires 3 - 5 GPH water).

Bulletin (from Manufacturer) -Adobe PDF file

HV Series Performance Specifications
HV- 1/2 - 1 ½" suction x 1" discharge
HV-1, HV- 1 ½, HV-2 – 2" suction x 1 ½" discharge
        performance curve

Model Number

Pressure @ 35 GPM

Pressure @ 60 GPM

Maximum Flow

Horsepower of motor

HV-1/2

25 feet

n/a

42 @ 9 feet

½

HV-3/4 35 feet 25 feet 80 @ 15 feet 3/4

HV-1

57 feet

40 feet

87 @ 23 feet

1

HV-1 ½

65 feet

56 feet

105@ 27 feet

1 ½

HV-2

73 feet

67 feet

125@ 35 feet

2



HN Series

Flows to 180 GPM
Pressures to 146 ft. TDH
Penguin-HN.jpg (29631 bytes)
3 to 7 1/2  horsepower

Recommended for:
Plating Solution Filtering/Circuit Etching
Fume Scrubbing/Pollution Control
Transfer Pumping
Recirculation Pumping/Water Treatment
Photographic Chemicals


Data Sheet

     HN Series  horizontal centrifugal pumps are designed to the latest hydraulic technology.  The volute design offer high efficiency and hydraulic balance for the impeller.  All units are supplied with a TEFC motor as standard.

Pump is constructed of CPVC thermoplastic.  Mechanical seal is carbon vs. ceramic (optional carbon vs. silicon carbide) with EPDM or Viton® elastomer.  The seal configuration can be outside mounted (standard) or double water flushed (requires 3 - 5 GPH water).

The pump's suction cover is closed using a T-bolt saddle -- allowing for easy service and reliable sealing using an O-ring.  HN Series pump are mounted on a 184JP motor -- this would allow motor being furnished by local sources.  

Bulletin (from Manufacturer) - Adobe PDF file


Return to Penguin Pump Index

HN Series Performance Specifications – 2 1/2" suction – 2" discharge

Performance Curve and Dimensions

Model Number Pressure @ 100 GPM Maximum Flow Motor
HN – 3 68 feet 156 @ 38 feet 3 HP
HN – 5 98 feet 170 @ 42 feet 5 HP
HN – 7 ½ 125 feet 181 @ 43 feet 7 1/2 HP


Note regarding the motor horsepower supplied with the pump - The required motor horsepower supplied for the pump may need to be increased dependent upon the specific gravity of the liquid being pumped. Use the below chart to adjust for specific gravity for HV and HN pumps.

Model Number

Specific gravity

Required HP


HV  1/2

1.0
1.0 – 1.5
1.5 – 2.0

½ *
¾ HP
1 HP


HV-3/4

1.0
1.1– 1.3
1.4 – 2.0

¾ *
1 HP
1 ½ HP


HV-1

1.0
1.1– 1.5
1.5 – 2.0

1 *
1 ½ HP
2 HP


HV-1 1/2

1.0
1.1– 1.3
1.3 – 2.0

1 ½*
2 HP
3 HP

HV-/2

1.0
1.1– 1.5

2 *
3 HP

HN-3

1.0
1.0– 1.6
1.3 – 2.5

3*
5 HP
7 ½ HP

HN-5

1.0
1.0– 1.5

5*
7 ½ HP

HN – 7 1/2

1.0

7 ½ *

* Indicates the standard motor horsepower for this model.

Return to Penguin Pumps Index

Viton® is a registered trademark of DuPont Dow Elastomers.